Newest Products

Makvona ModelPop: Paint Markers for Finishing 3D Prints

Makvona ModelPop marker set and painted 3D model

The print is finished, the supports are off, and a small dragon sits on your desk in one flat color. Giving its wings and scales some life sounds appealing. Setting out paint pots, a palette, and several brushes feels like another project.

Makvona ModelPop approaches that gap with a 36-color set of water-based acrylic paint markers designed for 3D prints. The appeal is straightforward: pick a color and paint directly onto a suitable prepared surface. It looks most useful for larger models, broad color areas, and quick accents. The important limit comes from Makvona itself: the tip cannot replace a fine detail brush for miniature eyes, narrow recesses, or very thin lines.

This feature is based on the creator's published campaign materials, not hands-on testing. The ModelPop Kickstarter campaign describes a painting tool, not a way to remove every finishing step.

Color a print without building a full painting station

ModelPop puts water-based acrylic paint into a marker format. Its semi-flexible tip has a stated reference stroke width of 1–6 mm, depending on pressure. That gives one tip room to cover an accessible panel and then add a smaller accent without changing tools.

Think of a decorative owl, a large character model, or the raised lettering on a printed sign. Those surfaces give the nib space to move. A deeply recessed eye socket is a different problem: even a flexible tip needs physical access. Makvona's FAQ recommends combining markers for main colors with a fine brush for the smallest details.

The distinction matters more than the number of colors. A set that makes you willing to finish a few larger prints may be useful even if it never replaces the brushes already on your desk.

Official before-and-after examples of 3D prints colored with ModelPop
Creator examples illustrate the intended change from plain prints to colored display models; they are not independent performance tests. Source: official ModelPop campaign.

Direct painting still starts with the surface

The campaign lists PLA, PETG, and properly washed and post-cured resin among its intended printing materials. Its preparation chart is more specific than the broad promise of painting straight onto a print: PLA should be clean and dry; PETG may need light sanding; resin needs washing and full post-curing.

The same chart includes ABS with a warning that some colors may shrink on its surface. Makvona advises testing a small area first. That caveat is worth keeping if your shelf contains prints made from several materials. Compatibility is not a promise that every filament formulation or surface finish will behave identically.

Primer is optional, according to the FAQ. A filler primer can still help soften visible layer lines and create a more even base. The markers add color; they do not physically smooth the ridges left by printing. A compatible clear coat is also optional, but the creator says to let the paint fully cure and test compatibility on a spare print first.

ModelPop official surface preparation chart for PLA PETG resin and ABS
The official material chart distinguishes direct painting from the preparation each surface still needs. Source: official ModelPop campaign.

Blending and layering are different jobs

For a gradient, Makvona recommends putting two colors next to each other and blending their meeting point while both remain wet. Small sections make sense here because the published blending window is approximately 20 seconds. The campaign's colorful wing examples show the intended effect, but your working time will depend on the surface, application, and conditions.

Layering follows the opposite rhythm. Let a coat dry, then add a thin layer with a light touch. The FAQ notes that lighter colors can need additional coats over darker ones. If you are correcting a small mark, plan for coverage rather than expecting every color to hide the one underneath in a single pass.

The specification sheet separates three timings: approximately 30–40 seconds to become touch-dry, a recommended recoat time of at least 60 seconds, and a recommended curing time of at least 24 hours. Touch-dry is therefore not the same as ready for every kind of handling or finishing.

The creator also says its paint minimizes unwanted spread into layer lines. That is a more useful expectation than treating the headline “No Bleeding” as an absolute guarantee. Test an inconspicuous area before outlining a feature you cannot easily repaint.

ModelPop official timing tip and storage specifications
The creator's specifications separate quick touch-drying from the longer recommended curing period. Source: official ModelPop campaign.

A replaceable tip, not an endlessly refillable pen

The reversible tip can be flipped to expose its fresh end. When both ends wear out, a compatible spare replaces it. The campaign's single-set reward lists 36 markers and 36 replacement tips. This could help you use paint remaining inside a marker after its nib deteriorates, but it is not a claim that the paint reservoir is refillable.

Care is fairly specific. Store the markers horizontally and recap tightly, including during short breaks. If the first strokes after storage look dark or uneven, the FAQ recommends gentle strokes on white scrap paper before touching the model. A hardened or heavily clogged tip should be replaced rather than scrubbed or pressed harder.

After blending, the same scrap-paper method helps clear a color picked up by the nib. The creator allows wiping wet paint from the plastic tip holder and cap with a slightly damp cloth, but says not to soak the marker.

ModelPop 36-color paint marker palette
The 36-color palette provides ready-to-use choices; finer shading still depends on technique and access to the model. Source: official ModelPop campaign.

What to check before backing

Buyer question What the campaign establishes Practical takeaway
Will it reach my details? Semi-flexible tip; reference strokes of 1–6 mm. Keep a fine brush for tiny eyes and tight recesses.
Can I skip preparation? Clean, dry surfaces; material-specific preparation. Check PETG and ABS on a small area; fully post-cure resin.
When can I add another coat? Recommended recoat time is at least 60 seconds. Do not confuse touch-drying with full curing.
Is the finish waterproof? Creator describes water resistance after full curing. Treat it as resistance to gentle wiping, not proven immersion protection.
What else costs money? Shipping is collected after the campaign; destination charges can apply. Check the reward and final delivered cost, not just the displayed pledge.

Rewards are denominated in Hong Kong dollars, although Kickstarter can also display approximate converted amounts. Availability, delivery estimates, and the eventual shipping charge should be checked on the live campaign. The project describes production-scaling risks, including consistent ink, color, and nib quality. Crowdfunding is not an in-stock retail order.

Who It Is For

ModelPop makes the strongest case for makers who enjoy printing larger display pieces but tend to leave them unpainted. It also fits small accents and touch-ups where bringing out a full paint setup would feel disproportionate.

It is less compelling as a complete replacement for a miniature painter's toolkit. Fine facial details, difficult angles, and highly controlled brushwork remain reasons to keep other tools. Anyone expecting a confirmed waterproof finish or no preparation on every plastic should also reset those expectations.

Summary

ModelPop's useful idea is a simpler entry into coloring 3D prints: a ready-made palette, a pressure-responsive tip, and replaceable nibs. Its limits are equally concrete: surface preparation, access to detail, drying versus curing, and the uncertainty of a campaign-stage product. Evaluate it as a convenient addition to a finishing workflow, not a substitute for every part of one. See the current rewards and creator updates on the official ModelPop Kickstarter page.

Editorial note: This article is an independent BackerRock analysis based on publicly available campaign information. It does not represent the position of Kickstarter, Indiegogo, or any crowdfunding platform, and should not be treated as investment, purchasing, or market advice.

Feature Your Project on BackerRock

Building a crowdfunding product? Explore BackerRock's campaign promotion services.

Explore BackerRock Promotion

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.